Leaking, Corroded, or Burst Pipes in Junction, TX? Masters Plumbing Service Fixes It
Pipe failures range from a slow pinhole leak weeping inside a wall to a full main line rupture. Locating the failure precisely — before opening drywall or digging — is the skill that separates a clean, affordable repair from an expensive and destructive guessing operation. Masters Plumbing Service's pipe technicians in Junction, TX use acoustic listening devices and thermal imaging cameras to find the leak first, then open only what needs to be opened.
What Separates Precision Pipe Repair from Guesswork
The biggest cost variable in pipe repair isn't parts — it's how much structure gets opened to find and access the failure. Precise pre-repair location tools reduce that cost significantly.
🔊
Acoustic Leak Detection
Pressurized water escaping a pipe creates a characteristic acoustic signature. Our listening devices amplify ground and structure-borne sound to pinpoint a leak location within inches — through concrete slabs, behind drywall, or under flooring. This means we open only the section of wall, floor, or slab directly over the failure.
🌡️
Thermal Camera Scanning
Active water leaks create temperature differentials on wall and floor surfaces detectable with an infrared camera. A slow leak inside a wall shows as a cold, spreading zone; a hot water line leak shows the inverse. Thermal imaging confirms leak presence and approximate location before any cutting begins.
🛠️
All Pipe Materials & Joining Methods
Press-fit copper connections — particularly useful for repairs in occupied spaces where open flame is a concern — are available as an alternative to torch sweating where code permits.
🔒
Pressure-Tested Before We Leave
Drain line repairs are water-tested by running fixtures through the repaired section and visually confirming no seepage at the repair joint and downstream.
Our Pipe Repair Services
Every Pipe Repair Type We Handle in Junction, TX
From a pinhole copper leak behind a kitchen cabinet to a full galvanized repiping, our pipe crew in Junction, TX handles the full range.
Copper
Copper Pipe Repair & Repipe
Copper failures most often involve pinhole corrosion in soft copper tubing from aggressive water chemistry, failed soldered joints, or fatigue cracks at fittings in high-vibration locations. We locate the failure precisely, cut out the failed section, and install either a sweated repair coupling or a press-fit connector — both rated to ASTM B88 standards for potable water service.
Galvanized
Galvanized Pipe Replacement
We replace galvanized supply lines with copper or PEX — either as targeted section replacement at active failure points or as a full-house repipe project. We connect the new material to existing fittings using dielectric unions where code requires to prevent galvanic corrosion at copper-to-galvanized transitions.
PEX
PEX Pipe Repair & Extension
Cross-linked polyethylene (PEX) is the current standard for residential supply piping. Failures are uncommon but occur at crimp or clamp fittings that were improperly installed, at pipe runs exposed to UV degradation, or at locations where the pipe was kinked during installation. We repair using expansion fittings (for PEX-A) or crimp fittings with the correct ring size for the pipe diameter.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
We also inspect upstream of the burst for additional sections that froze but haven't yet failed — because a partially-thawed line sometimes shows multiple failure points only after pressure is restored.
Slab Leaks
Under-Slab Pipe Leak Repair
Supply line leaks under a concrete slab are identified by acoustic detection and confirmed by thermal imaging. Once located, we evaluate three repair options: direct-access repair (jackhammering to the pipe, repairing the section, and patching the slab); rerouting the line through the wall framing above slab to bypass the failed underground run; or epoxy pipe lining for older copper systems with systemic pinhole corrosion.
Full Repipe
Whole-House Repipe Service
When galvanized supply lines are at end of life or polybutylene pipe (recalled for chronic failure) is in the home, a full repipe with PEX or copper is the permanent solution. We run new supply lines through the structure, transition all fixture connections, pressure test the entire new system, and patch access points in walls and ceilings.
We don't open walls at random. Acoustic and thermal detection tools tell us exactly where to cut before we pick up a saw.
1
Call & Describe — We Shut the Water If Needed
Active leak? Our dispatcher walks you through shutting off the main supply valve while we drive to you. Describing what you see — water stain on a ceiling, drop in water pressure, wet flooring — helps us arrive with the right detection tools loaded.
2
Pressure Test & Acoustic / Thermal Detection
This detection step routinely saves homeowners $500–$2,000 in unnecessary drywall removal compared to opening walls speculatively.
3
Flat-Rate Quote & Minimal Access Opening
For slab leaks, we present repair, reroute, and lining options with pricing so you can make an informed choice before any concrete is cut.
4
Repair & Pressure Test — Then You're Done
Repair executes immediately on approval. After the repair, we repressurize and hold a pressure test to confirm the failure is fully resolved — not partially. The access opening is left clean for your drywall patch or left ready for your contractor.
Customer Reviews
Masters Plumbing Service Pipe Repair — How We Handle It
★★★★★
Water stain appeared on my kitchen ceiling from the bathroom above. I expected them to tear up the entire bathroom floor. Instead the tech ran a pressure test, found a 12% pressure drop over 10 minutes, then used the acoustic device and identified the leak at a failed sweat joint in the copper supply to the toilet — accessible through a 14-inch drywall cut in the ceiling below. Repair was maybe $280 including the detection. I'd been dreading a $2,000 floor demo.
— N. Bergman, Junction
★★★★★
Our galvanized supply lines finally gave out — low pressure everywhere, rust-colored water at some fixtures. Masters Plumbing Service repiped the whole house with PEX over two days. They confirmed pressure and flow at every fixture before leaving, patched all the wall access points smooth, and cleaned up each work area. One year later, no issues at all.
— O. & R. Adeyemi, Junction, TX
★★★★★
I noticed my water meter spinning with all fixtures off — confirmed a leak in the supply system. Masters Plumbing Service ran a pressure test and acoustic scan, found a pinhole in a copper section under the slab in the utility room. They rerouted the line through the wall above slab, tested, and closed out the permit. The reroute was exactly the same cost as direct slab access would have been, but no damaged floor tile.
— F. Okoro, Junction, TX
Common Questions
Pipe Repair FAQ for Junction, TX Homeowners
Watch your water meter with all fixtures off. If the meter dial is moving or the leak indicator light is turning, water is escaping somewhere in your supply system. Other signs: unexplained increases in your monthly water bill, soft or discolored spots on walls or ceilings, mold or mildew smell in a room without a visible source, or a running sound inside walls when all fixtures are off.
In most cases, the pipe itself needs to be physically accessed to make a durable repair — but the amount of wall we open depends entirely on how precisely we can locate the failure first. With acoustic detection and thermal imaging, we typically open a single, small access point rather than a wide section of wall.
A slab leak is a supply line or drain line failure in a pipe that runs through or under the concrete foundation slab. Supply line slab leaks are the more urgent scenario — pressurized water escaping under the slab saturates the subgrade, can undermine the foundation, and drives significant water bills.
Galvanized pipe corrodes from the interior outward — by the time one section fails, the rest of the pipe is in varying stages of the same process. A localized repair buys time, but another section typically fails within 1–3 years if the system is at end of life. The honest answer is: it depends on how far along the corrosion is and how many sections are already narrowed or showing surface rust.
We don't rush pressure testing at the end. That's the step that confirms the repair is actually complete, and it takes the time it takes.
Our pipe repair quote includes clean access cuts and leaving the opening ready for patching — with a clean, straight cut that accepts a standard drywall patch. We can typically patch the access opening as part of the job on request, though finish painting and texture matching are typically handled by the homeowner or a drywall contractor for best cosmetic results.
Service Area
Your Local Pipe Repair Specialists in Junction, TX
Our techs are stocked with the copper, PEX, and CPVC materials most commonly needed in Junction homes and businesses.
Burst or Leaking Pipe? Call +1-855-718-1500 Right Now
Active pipe leaks compound fast — mold growth can begin in 24–48 hours of sustained moisture. Masters Plumbing Service's pipe repair crew is in Junction today, equipped with acoustic and thermal detection tools to find the failure precisely before anything is opened.
